Vinyl

Wetroom Vinyl System

Watertight vinyl systems with welded seams, integrated drains and coving for showers & wet zones in healthcare, MFH and hospitality. B2B supply & installation.

2.0–3.0 mm
Thickness
R10–R11
Slip rating
10+ years
Service life
Wetroom Vinyl System
R10–R11Bfl‑s1Barefoot
Wetroom Systems
Changing rooms·Bathrooms·Wellness

What It Is & Where It Works

A wetroom vinyl system is a coordinated set of vinyl sheet floors and walls with hot‑welded seams, waterproof membranes, integrated drains, coved skirtings/upstands and prefabricated corners. The aim is to achieve a continuous, watertight and hygienic surface for showers and permanently wet areas.

Healthcare

Treatment rooms, patient bathrooms, staff showers and decontamination zones.

Multi‑Family Housing

Ensuite showers, family bathrooms and shared amenity wetrooms in residential towers.

Hospitality

Hotel bathrooms, spa & wellness circuits, steam rooms and pool changing areas.

Education & Public

Locker rooms, team showers, public pools and sports facility changing blocks.

Office & Amenity

End‑of‑trip showers, cyclist facilities and wellness rooms in corporate fit‑outs.

Marine & Offshore

Crew showers and wet heads where sheet vinyl with welded seams is a proven solution.

Why Specify Vinyl Wetrooms

  • Guaranteed waterproofing

    When installed to the system detail — membrane + welded seams + compatible drains.

  • Seamless hygiene

    Continuous surfaces without grout lines; clean with neutral detergents/disinfectants.

  • Slip control

    Wet‑area surface textures and targeted R‑ratings where required by code.

  • Accessibility

    Flush thresholds, coved junctions and preformed slopes towards drains.

  • Lifecycle value

    Fewer water‑ingress risks vs. grout; easier refresh of surfaces when required.

  • Design coordination

    Floors & walls in harmonized tones, non‑slip textures and contrast options.

Technical & Compliance

Always confirm exact values and detailing for your chosen system and jurisdiction (datasheet/DoP/installation manual).

  • Waterproofing

    Membrane + hot‑welded seams + welded/locked drain interface.

  • Drains

    Linear or point drains; vinyl‑compatible flanges; clamping rings.

  • Slopes

    Pre‑formed or screeded falls towards drains (by installer).

  • Slip resistance

    Wet‑area textures; specify R‑rating per local code (typically R10–R11).

  • Fire performance

    Flooring typically Bfl‑s1; wall B‑s2, d0 (verify DoP/test).

  • Indoor air

    Low VOC; request certificates (M1 / FloorScore / equivalent).

  • Walls

    Vinyl wallcovering / hygienic panels with sealed seams.

  • Corners & upstands

    Preformed corners, coved skirtings, upstands at perimeters/penetrations.

System Components

  • Vinyl sheet flooring

    Rated for wet use, with hot‑welded seams.

  • Waterproof membrane

    Under or integrated, as per system.

  • Drain kits

    Linear/point drains with compatible flanges for vinyl welding.

  • Coved skirting / upstands

    Using preformed coves or site‑formed with capping strips.

  • Prefabricated corners

    Internal/external corners for consistent, repeatable detailing.

  • Wall vinyl

    Or hygienic wallcovering with sealed joints for splash protection.

  • Sealants, rods, trims

    And accessories specified per system.

Wetroom vs LVT/SPC in Bathrooms

Rule of thumb: for showers and permanently wet zones, specify a wetroom sheet system with welded seams. LVT/SPC modular systems are not designed for continuous wet use.

Criterion

Wetroom Vinyl (Sheet)

LVT / SPC (Modular)

Design & Detailing Notes

The wetroom detail is only as good as its weakest junction. These are the design checkpoints that typically separate a trouble‑free 10‑year wetroom from an early failure.

  • Substrate prep

    Ensure flatness and moisture control; prime/screed to manufacturer guidance.

  • Falls / slope design

    Plan consistent falls to drains; avoid low points away from the drain.

  • Door thresholds

    Design flush entries with water barriers as needed; coordinate with corridor finish.

  • Penetrations

    Seal around pipes, rails, benches with compatible collars/sealants.

  • Wall junctions

    Continue upstands behind fixtures; maintain welded or sealed joints.

  • Contrast & wayfinding

    Use high‑contrast textures/colours for accessibility in clinical / elderly housing.

Sector Guidance

Wetroom detailing shifts sharply between sectors — here is how we typically match specification to environment so the system lands right the first time.

01

Healthcare

Use preformed corners, coved upstands and clinical drain kits; document chemical resistance for cleaning and disinfection agents.

02

MFH & Hospitality

For ensuite showers, use compact linear drains; coordinate wall finishes for steam and humidity performance over the building’s life.

03

Education & Public

Locker rooms and team showers: plan high‑traffic slip control and robust corner/edge protection for heavy daily use.

Logistics & B2B Supply

Materials supply with optional [professional installation](/flooring-installation/), including wetroom systems. Or use your own wetroom contractor.

Order sizes:

Full system kits (floor / wall vinyl, drains, corners, rods) to palletized supply.

Lead time:

Stock vs made‑to‑order colours and drain types.

Docs:

Datasheets, DoP/DoC, fire/slip tests, installation manuals, EPD on request.

Samples:

Texture chips, colour boards.

Support:

Spec wording, detail drawings, maintenance guides.

FAQ

Here you’ll find answers to the most common questions our customers ask when specifying wetroom vinyl. If you don’t see the information you’re looking for, feel free to contact our support team — we’re always here to help.

01

Can I use LVT or SPC inside the shower area?

+

No. For showers and permanent wet zones, specify wetroom vinyl sheet with welded seams and a compatible drain kit.

02

Do you provide the drain?

+

We supply drain kits compatible with vinyl welding (system‑dependent), or coordinate with your approved drain supplier.

03

How are corners and upstands formed?

+

Use preformed internal/external corners and coved skirtings/upstands to achieve continuous waterproof detailing.

04

What slip rating is required?

+

Specify wet‑area textures and match the R‑rating required by local code for showers/changing rooms.

05

Do you install?

+

We focus on materials supply, but we also offer professional flooring installation. Alternatively, use your own specialist contractor.

Ready to specify a Wetroom System?

  • Request Specs & Commercial Offer (area m², drain type, slope detail, wall finish, timeline, delivery region).
  • Order Samples (texture set, colour shortlist).
Ready to specify a Wetroom System?

Products in this category